Mud and Lameness in Beef Cattle

Cattle in a muddy lot.
Cattle in a muddy lot.
(University of Nebraska-Lincoln )

Melting snow and spring rains produce conditions that can increase lameness in beef cattle. Mud is among the predisposing causes for cattle lameness. Wetness decreases hoof hardness and increases the incidence of claw lesions. Research has shown that nearly one-third of the total water absorbed by the hoof happens during the first hour of exposure to high moisture resulting in heavier and softer hooves. Although not as prevalent as observed in the dairy industry, when it happens it may lead to decreased feed intake, lower weight gains, reduced reproduction (both in cows and bulls), and greater culling rates.

Beef producers address muddy conditions by creating mounds where cattle can lay down on higher, drier ground. There is minimal cost to establish a mound particularly when the shaping takes place previous to installing fences, bunks, watering, and aprons. With a slope of usually 3 to 5%, mounds work best when built parallel to the direction of the slope and are located in the center-line of the pen. In older lots these mounds can be newly built or strengthened periodically by adding manure and dirt. Mounds, however, do not last forever and more than likely will need some reshaping with additional material yearly. The main concern is when either by accident small rocks or pebbles are present in the material used to build them.

Standing cattle apply a significant amount of pressure to any surface. In a 2017 University of Kentucky article researchers compared this pressure with that of other livestock, humans, and farm equipment. Pressure was measured in pounds per square inch (psi) or, more accurately, pound-force per square inch. One Psi is the pressure that results from a force of one pound-force on an area of one square inch (Table 1). From the data in the table it is obvious that aside from tractors, cattle and horses exert the most pressure per square inch, even more than a 50-ton bulldozer!

The reader is probably aware of the “action-reaction physics principle”; in simple terms it states that every action, is followed by an equal and opposite reaction force. For example, if you press a button, the button presses back with the same amount of force! This brings us back to the issue of beef cattle mounds and the presence of stones or other foreign objects. When mounds are not maintained (or reshaped) regularly, rains or any other source of running water erodes their surface and expose these underlying hard objects. Consider now the force cattle make on this surface (Table 1), and the resulting pressure back on hooves that have already been softened by constant exposure to water. When cows walk however, they apply this pressure to two extremities at a time, increasing the pressure per square inch (Table 2). As a result, cow’s extremities sink deeper in the mud reaching oftentimes the subjacent hardened surface, which could have hard objects not visible at plain sight.

Table 1. Pressure created by different stressors
Stressors Pressure (Psi)
Sheep 12
Human 14
Utility terrain vehicle 14
50-ton bulldozer 16
Cattle 27
Horse 27
Tractor 175
Higgins et al. Revised 2017

 

 

 

 

 

 

 

 

Table 2. Pressure created by walking humans and livestock
Stressors Pressure (Psi)
Humans 28
Cattle 48
Horses 48
Higgins et al. Revised 2017

 

 

 

 

 

 

Although not as prevalent as lameness in dairy cattle, there are infectious agents (i.e. Fusobacterium necrophorus and Bacteroides melaninogenicus) that can cause cattle lameness, foot rot, and digital dermatitis or hairy heel warts. Warts are most likely caused by Spirochetes, which is still one of the leading causes of lameness in the U.S. Beef producers should manage cattle attempting to keep hooves as dry as possible. Since this is very difficult in most farms particularly during spring or in unusually wet years, it is important to find ways to reduce the incidence of injuries to the hoof. This can be accomplished by periodically walking the pens to remove foreign objects and being careful with the type of material used to reshape the mounds.

 

Latest News

Biden Administration Restores Wildlife Protections
Biden Administration Restores Wildlife Protections

The U.S. Fish and Wildlife Service plans to reinstate rules protecting endangered plants and animals, action that would reverse changes made during the Trump Administration that weakened the Endangered Species Act.

Across Breed EPD Adjustment Factors
Across Breed EPD Adjustment Factors

EPDs from multiple breeds can be compared by adding/subtracting the appropriate adjustment factors to the EPDs resulting from the most recent genetic evaluations for each of 18 breeds.

APHIS Now Thinks Wild Birds Are to Blame for Highly Pathogenic Avian Influenza's Arrival on Four U.S. Dairies
APHIS Now Thinks Wild Birds Are to Blame for Highly Pathogenic Avian Influenza's Arrival on Four U.S. Dairies

The livestock industry continues to grapple with the first confirmed cases of HPAI in cattle, while federal and state agencies continue to assure consumers there's no concern about the safety of the U.S. milk supply.

Skills Survey Reveals U.S. Agriculture & Food Industry Workforce Needs and Gaps
Skills Survey Reveals U.S. Agriculture & Food Industry Workforce Needs and Gaps

U.S. employers report challenges in finding suitable job candidates with work-ready skills to fill open roles in ag. The AgCareers.com U.S. Skills Survey offers insights, data and trends to address skill development.

USDA Authorizes CRP Graze and Hay Donations to Wildfire Victims
USDA Authorizes CRP Graze and Hay Donations to Wildfire Victims

Conservation Reserve Program (CRP) participants can donate emergency grazing authority to ranchers in Nebraska, Oklahoma and Texas impacted by recent wildfires.

New Guide Helps Producers Maximize Values of Cull Cows
New Guide Helps Producers Maximize Values of Cull Cows

A new resource developed by the National Cattlemen’s Beef Association and CattleFax helps cattle producers maximize profitability from their culling decisions.