The 5 Steps for A.I. Success

Semen should then be thawed at 95°F for 45 seconds. If this temperature is not accurate, the improper thawing could affect the quality and viability of the semen
Semen should then be thawed at 95°F for 45 seconds. If this temperature is not accurate, the improper thawing could affect the quality and viability of the semen
(Taylor Leach)

There’s no bull about it, artificial insemination (A.I.) has come a long way since its first use in dairy cattle during the late 1930s. While the technology has vastly changed, the basic principles still remain. Karen Johnson, an Extension educator at the University of Minnesota, provides these five steps for A.I. breeding success:

1. Proper Semen Handling – Depending on the sire, semen costs can add up quickly. Therefore, it’s crucial to make sure you handle the semen properly. Johnson recommends using tweezers to handle the semen straw as your fingers could potentially lead to the semen thawing too quickly. Additionally, if you are breeding multiple animals, she suggests only handling the number of straws that you can successfully use within 15 minutes of thawing.

Once the straw is removed from the tank, shake it to eliminate any liquid nitrogen at the end of the cotton plug. The semen should then be thawed at 95°F for 45 seconds. If this temperature is not accurate, the improper thawing could affect the quality and viability of the semen, according to Johnson.

 

2. Loading the Breeding Gun – Once the semen has been thawed, it’s time to load the breeding gun. Johnson suggests warming the gun by stroking it vigorously with your hand five or six times. Next, pull the plunger back about 6 inches and place the straw inside with the cotton plug first. From there, cut the sealed end of the straw at a 90° angle to ensure that the plastic sheath seals tightly to prevent back flow and then place the breeding gun between your body and shirt to maintain the optimal temperature.

 

3. Breeding the Cow – “It is recommended to use your left hand in the rectum and right hand to guide the insemination gun regardless of your dominant hand,” Johnson says. “Use a new breeding glove for every insemination and lubricate the glove with mineral oil or a commercial A.I. lubricant.”

Forming a cone like shape with your fingers, gently enter the rectum and palpate to remove excess manure. Next, clean the vulva to prevent contamination and slowly insert the gun. Johnson recommends inserting upwards at a 30° angle to prevent the gun from accidently entering the bladder.

“When the gun is 6 inches to 8 inches inside the vagina, raise the rear of the gun to level position and slide forward until it contacts the beginning of the cervix,” Johnson says. “If the gun is getting caught in the folds of the cervix, try stretching the cervix away from you with your left hand to free the gun and allow easier passage to the cervix.”

Once the cervix has been located, manipulate it slightly to detect the cervical rings. Work your way through the rings, but never use force. The gun should slide freely with little resistance once the rings have been cleared.

 

4. Depositing – After entering the cervix, it’s time to deposit the semen.

“Ideally, semen should be deposited just beyond the cervix into the uterine body,” Johnson says. “Depositing the semen in the uterine body allows the semen to evenly distribute between both horns.”

Using the plunger, slowly deposit the semen. This should take roughly five seconds according to Johnson. Make sure your palpating hand is not blocking the flow of semen and do not pull back on the cervix. Once finished, gently remove the gun. Johnson suggests checking for any abnormal discharge and noting it in your breeding records.

 

5. Clean Up – Last, but not least, it’s time to clean your equipment. Before taking off your breeding glove, remove the used sheath. Then dispose of your used glove and clean equipment thoroughly. Lastly, recheck to make sure the desired bull was used and note all information in your breeding records.

 

Latest News

Across Breed EPD Adjustment Factors
Across Breed EPD Adjustment Factors

EPDs from multiple breeds can be compared by adding/subtracting the appropriate adjustment factors to the EPDs resulting from the most recent genetic evaluations for each of 18 breeds.

APHIS Now Thinks Wild Birds Are to Blame for Highly Pathogenic Avian Influenza's Arrival on Four U.S. Dairies
APHIS Now Thinks Wild Birds Are to Blame for Highly Pathogenic Avian Influenza's Arrival on Four U.S. Dairies

The livestock industry continues to grapple with the first confirmed cases of HPAI in cattle, while federal and state agencies continue to assure consumers there's no concern about the safety of the U.S. milk supply.

Skills Survey Reveals U.S. Agriculture & Food Industry Workforce Needs and Gaps
Skills Survey Reveals U.S. Agriculture & Food Industry Workforce Needs and Gaps

U.S. employers report challenges in finding suitable job candidates with work-ready skills to fill open roles in ag. The AgCareers.com U.S. Skills Survey offers insights, data and trends to address skill development.

USDA Authorizes CRP Graze and Hay Donations to Wildfire Victims
USDA Authorizes CRP Graze and Hay Donations to Wildfire Victims

Conservation Reserve Program (CRP) participants can donate emergency grazing authority to ranchers in Nebraska, Oklahoma and Texas impacted by recent wildfires.

New Guide Helps Producers Maximize Values of Cull Cows
New Guide Helps Producers Maximize Values of Cull Cows

A new resource developed by the National Cattlemen’s Beef Association and CattleFax helps cattle producers maximize profitability from their culling decisions.

How Ranchers can Feel More Energized and Reduce their Aches and Pains
How Ranchers can Feel More Energized and Reduce their Aches and Pains

We can’t care for our livestock, resources and families without caring for ourselves first. That seems even harder during the busy seasons, but it isn’t impossible and even one thing a day makes a difference.