Managing Late-Season Corn – Fighting Frost Damage

( Sponsored Content )

Given the late planting season many farmers experienced this year, it’s quite possible that silage harvest will be later than normal. A late harvest and cool autumn temperatures can create a recipe for frost damage. The extent of the frost damage on the corn depends on the temperature, duration of the temperature and corn growth stage at the time of the frost, write Chad Lee and James Herbek, University of Kentucky grain crops Extension specialists.

Conditions for a Frost

Air temperature below 32°F for four to five hours will result in frost damage to the stalk, leaf and husk. Air temperatures that drop to 28°F for a few minutes and return to 32°F can result in similar injury. Air temperatures between 32°F and 40°F typically result in less frost damage.

Frost at temperatures above 32°F usually occurs under conditions of clear skies, low humidity and no wind. These conditions are ideal for rapid heat loss from the corn leaves. Under these conditions, temperature of the corn leaves can be less than the air temperature. Thin stands of corn and corn stands at the edges of fields are more likely to receive frost damage at temperatures above 32°F than thicker stands and the centers of fields. The uppermost leaves of the corn plant are most susceptible to frost damage at temperatures between 32°F and 40°F.

Growth Stage at Time of Frost

Management of corn damaged by frost will depend on the stage of growth at the time of frost. Corn will ensile well at moisture levels less than 70% for upright silos and less than 75% moisture for horizontal silos. Corn harvested at 62% to 68% moisture (late-dent stage) is ideal for ensiling. Frost damage prior to late-dent stage will result in corn that is too moist for silage harvest. Frost at these higher moistures will reduce yields and may reduce quality.

QSqs2

Frost at Milk Stage

When a frost occurs at the milk stage, the moisture content of the plant is too high for proper ensiling. The leaves of the plant will dry very quickly, which causes the entire plant to appear to be drying more quickly. However, the entire plant will dry down similarly to corn that was not injured by frost. If the corn at milk stage is ensiled immediately after frost, then nutrients will leach away, silage will be sour and wet, and livestock consumption will be low.

Waiting to harvest frost-damaged corn at the milk stage will improve silage quality but will decrease dry matter yield. Up to 10% dry matter losses will occur the first 10 days after the frost and up to 20% dry matter will be lost 40 days after the frost. In addition, mold may develop in the ears and cause further yield reductions. Because of these factors, a compromise between dry matter yield and ideal ensiling moisture must be made.

In some cases, the corn will need to be harvested when it is too wet for silage. In these situations, chopped grain, hay or straw can be added to the silage to decrease overall moisture. In general, 30 lb. of dry matter per ton of silage are required to reduce the moisture percentage by one point.

One concern of frost occurring at the milk stage is high nitrate levels. High nitrate levels are toxic to cattle and will occur most frequently when the corn has been under drought stress prior to the frost. Ensiling will reduce nitrate levels 40% to 60%. To reduce the risk of nitrate toxicity, allow the ensiling process to occur for at least 21 days before feeding.

Another option for corn with high moisture content is to feed the corn as green chop. Cattle will consume less green-chop corn than ensiled corn. However, the quality of the frost-damaged, green-chopped corn is better than the quality of the ensiled corn at milk stage. If the corn is to be fed as green chop, then check the corn for nitrate levels, which is usually available through your county Extension office.  

 

Frost at Dough Stage

If a frost occurs when the corn is at the dough stage, then whole corn is often too wet for silage harvest. Typically, several drying days are necessary before whole corn will be at the proper moisture for silage harvest. The corn should be harvested as soon as it reaches the desired moisture of 70% to 75%. The balance between waiting to harvest corn for silage at the ideal moisture and harvesting to prevent yield loss still must be considered. However, corn damaged by frost during the dough stage will require less time to dry down than corn damaged during the milk stage.

 

Frost at the Dent Stage

If a frost occurs when corn is at the early-dent stage, then whole corn may need to dry a couple days before it is ready to harvest. If a frost occurs when the corn is at the mid- to late-dent stage, whole corn is at or very close to ideal moistures for ensiling. Corn damaged by frost at the mid- to late-dent stage should be harvested for silage immediately because whole plant moisture should be close to ideal for harvest and waiting for harvest could cause yield reductions.

Summary

Management of frost damage to corn grown for silage depends in part on the stage of growth when the frost occurred. Waiting to harvest frost-damaged corn will improve silage quality but will decrease dry matter yield. Producers must balance between expected yield losses and quality gains by waiting to harvest.

 

You can find the full article here.

Originally published by Chad Lee and James Herbek, grain crops Extension specialists

 

Photo courtesy of University of Minnesota

 

 

To read more articles like this one:

Dairy Herd Management

Prussic Acid and Nitrate Poisoning are Concerns After a Light Frost

Fall frost and alfalfa: Risk management in play for growers

This Is Not A Typical Year For Corn Silage

Drovers

How Likely is an Early Frost?

Frost can turn a good pasture deadly

Here’s What an Early Frost can Do To Corn Silage

 

 

Sponsored by Lallemand Animal Nutrition

 

Comments